Active Deterrence Setup

Introduction

• Arm/Disarm (ADW2)

• Arm/Disarm (ADW1)

• NVR Arm/Disarm
• Uploading Audio

• Smart Illumination Mode Setup

• Triggering Active Deterrence from IC View+

The IPMX-B40F-ADW1/2 and IPMX-E40F-ADW1/2 IP cameras feature Audio and Visual active deterrence using their built-in speakers and Blue+ Red LEDs. 

Active deterrence can be triggered by Motion Detect/ Intelligent Motion Detect or IVS/ Perimeter Protection (Tripwire and Intrusion). These features can be accessed by logging in directly to the ADW camera web interface.  

________________________________________________________________________________________________________________

Active Deterrence Setup

Arm/Disarm (AD-W2)

1.  Log in to the IP address of the camera using a web browser. (Initialize the camera if necessary)
2. Under the Settings cog, click on Event -> Disarming. Select Disarming once disarming is enabled this will turn off all alarms on the camera.
3. Once Disarm by Period has been enabled, select Custom in the drop down menu, and select Add Schedule. 

Alarm Period Settings (AD-W2)

4) Click and drag the schedule bar to the desired time frame. If you need additional periods you can click and drag on the time bar. Once you have made your desired selection click apply.

________________________________________________________________________________________________________________

Arm/Disarm 

Web GUI: You can manually turn off the active deterrence features under  Settings > Event > Disarming. 

Disarm Period Setting: You can also set a disarm schedule for the selected Alarm Linkages shown below. Keep in mind that "green" bars on the disarm period setting will indicate times of "disarm," ie: when the chosen Alarm Linkages will be disabled (such as Warning lights and Audio Linkages).

ADW1 shown below:

ADW2 shown below:

Arm/Disarm using IC View+

You can setup the Arm/ Disarm using the IC View+ mobile app.  This feature is available when connecting IC VIew+ directly to an ADW camera or a compatible NVR (EL series NVRs with 4.0 UI and MX/FX 16MP series)

1. Go to Home () then tap the  icon, then tap on Device Details.
2. Under Alarm Settings, you can tap the toggle to enable/ disable Alarm Linkage.
   
   

________________________________________________________________________________________________________________

Uploading Audio

You can upload or record your own custom audio to the camera to enhance the Audio Deterrence effect. 

1. Log in to the Camera Web GUI. Go to the Setting tab, then Camera > Audio > Alarm Audio.

2. Click the "Add Audio File" box. A prompt will appear.

3. If Selecting Upload, the file type must be in .wav format. Click the folder icon to browse and select the desired file. Click "Upload" to save.

If Selecting Record, the Camera microphone (or line-in, if installed and selected) will be used to record the audio. Type in a file name for the recording, then click on the Record button to record the audio from the camera. Click on Stop when finished to save.

________________________________________________________________________________________________________________

NVR Arm/Disarm

Similar to the AD-W2 cameras, most up-to-date IC Realtime NVR's on the 4.0 Firmware now come equipped with disarming settings right inside the recorder for alarms including the AD series cameras.

Navigate to:

Advanced Settings -> Alert Center -> Disarming

1. Once Disarming has been enabled, this will disarm all alarms by default unless you check the listed boxes.
   • Select Disarm by Period and select Setting. To select a specified schedule for the alarms.
2. To select a specific channel, check the box at the bottom of the page to activate and click Setting to set the desired channels

________________________________________________________________________________________________________________

Smart Illumination Mode Setup

The IPMX-B40F-ADW2 and IPMX-E40F-ADW2 IP cameras feature not only Active Deterrence features but also Dual Illumination. These cameras can be configured for: White Light, IR, Smart Illumination (default) or By Time/Scheduled mode.

1. Log in to the IP address of the camera using a web browser. (Initialize the camera if necessary)
2. Navigate to Settings > Camera > Image > Illuminator. Under Fill Light dropdown, select the desired mode.
   

• Smart Illumination: When enabled, the camera will go to a low-visibility IR mode until an event has been triggered, which turns on the White Light LED (and any Active Deterrence such as sound/ voice prompts and/ or the blue+ red flashing lights) to help identify the target. The camera will return to IR mode when the target leaves the scene.
• IR Mode: Only IR lights will be used for illumination. Can be set to Manual, Auto, or Off.
• Warm Light Mode: Only White Light LEDs will be used for illumination. Can be set to Manual, Auto, or Off.
• By Time (Scheduled): Here, you can configure different illumination modes for specific days of the week and time periods. Click Setting under Time Plan to set up the schedule. 
  
  
  

________________________________________________________________________________________________________________

Triggering Active Deterrence from IC View+

With the IC View+ Mobile app, you can manually trigger the Active Deterrence functions.

1. Add the ADW Camera (or a  Recorder with the ADW camera) to the IC View+ App.
2.  While on a single split view displaying the ADW camera, tap on the expanded options icon 
3. Tap on the icon to open the Active Deterrence Menu.
4. Tap on the respective icons to trigger the Red and Blue lights or the Siren.